Close
Owls CMS
Owls CMS
Contact us
products
Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62

products

Products of eyvaz company
Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62

Product information

  • Product Title : Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62
  • Production code : (TDS 30-62 (F, T, S
  • Professional Name : Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62

General information Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62

 Steam traps are used to remove condensate from steam lines. This type of trap is applied for high pressures, and has such capacity to get repaired without separating from the pipeline. It is equipped with a bimetal ring to drain excess air in the system. It has a high discharge capacity due to its low weight and volume, and also the ability to be installed in different directions. Moreover, it has good resistance against the frost and water hammer.

Function Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62

The thermodynamic trap is an extremely robust steam trap with a simple mode of operation. The trap operates by means of the dynamic effect of flash steam as it passes through the trap, as depicted in the image below. The only moving part is the disc above the flat face inside the control chamber or cap.

On start-up, incoming pressure raises the disc, and cool condensate plus air is immediately discharged from the inner ring, under the disc, and out through three peripheral outlets.

Hot condensate flowing through the inlet passage into the chamber under the disc drops in pressure and releases flash steam moving at high velocity. This high velocity creates a low pressure area under the disc, drawing it towards its seat .

Installation Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62

The Thermodynamic Trap should be installed in a horizontal plane such that disc movement happens only in vertically up and down directions.

Download product Catalogue and installation tutorial Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62

Product Catalogue Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Manual installation - PDF Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62 Thermodynamic Steam Trap With Bimetallic Air Vent Type TDS 30-62

:

I to P Positioner Type 3730-1 Samson

I to P Positioner Type 3730-1 Samson

I TO P positioner is used for controlling the valve with Type NCV 24-11 by input flow. .

Analog Thermostatic Sensor TS Type 22-31

Analog Thermostatic Sensor TS Type 22-31

Analog Thermostatic Sensor TS Type 22-31 works based on physical rule of liquid expansion. Temperature sensor of this device is placed inside the tank….

Manual Thermostatic Sensor TS Type 22-41

Manual Thermostatic Sensor TS Type 22-41

the safe operation of unit is guaranteed if only it is installed, started up and maintained by qualified and skilled person, and most importantly, based….

Magnetic Sensor for Magnetic Level Gauge Type MS15

Magnetic Sensor for Magnetic Level Gauge Type MS15

Magnetic Sensor type MS15 install next to the Level Gauge. When the floater goes up exist magnetic field and finally change to the micro switch..

Thermostatic Steam Trap TST 30-21

Thermostatic Steam Trap TST 30-21

TST 30-21 contains flat strainer , small body and low discharge capacity and it is produced and tested base on  DIN standards ,this device is appropriate….

Stainlesssteel Vacuum Breaker Type SVB 40-10

Stainlesssteel Vacuum Breaker Type SVB 40-10

In air and compressed gasses system, humidity of air and gases is usually converted to condensate and flocked in the system. This condensate causes to….

Brass Vacuum Breaker type BVB 40-16

Brass Vacuum Breaker type BVB 40-16

In liquid line, vacuum sometimes is occured. This event causes to appropriate movement of liquid and decrease efficiency of system or during draining….

Control Pressure Switch Type CPS 20-62

Control Pressure Switch Type CPS 20-62

The foundation of Control Pressure Switch Type CPS 20-62 is electromechanical.This kind of pressure switch is usually mounted vertically on the top of….

Control Pressure Switch Type CPS 20-61

Control Pressure Switch Type CPS 20-61

The foundation of pressure switch is electromechanical.    .

Mechanical Level Switch Type MLS 20-02

Mechanical Level Switch Type MLS 20-02

Function of this device is based on electro-mechanical. With change of liquid level, the floater ball with connected lever move up and down (vertically).the….